Panel Mounted Ratings - Select model on actual motor full load current
 
Unidrive SP
Normal Duty
Heavy Duty
Max Cont
Current
Typical Motor
Output Power
Max Cont
Current
Typical Motor
Output Power
Modules
Frame
(A)
(kW)
(HP)
(A)
(kW)
(HP)
200-240VAC (kW@220V HP@230V) ±10%

SP1201

 1

5.2

1.1

1.5

4.3

0.75

1.0

SP1202

6.8

1.5

2.0

5.8

1.1

1.5

SP1203

9.6

2.2

3.0

7.5

1.5

2.0

SP1204

11.0

3.0

3.0

10.6

2.2

3.0

SP2201

 2

15.5

4.0

5.0

12.6

3.0

3.0

SP2202

22.0

5.5

7.5

17.0

4.0

5.0
SP2203
28.0 7.5 10.0 25.0 5.5 7.5

SP3201

 3

42.0

11.0

15.0

31.0

7.5

10.0

SP3202

54.0

15.0

20.0

42.0

11.0

15.0
SP4201
4 68.0 18.5 25.0 56.0 15.0 20.0
SP4202
80.0 22.0 30.0 68.0 18.5 25.0
SP4203
104 30.0 40.0 80.0 22.0 30.0
 
Panel Mounted Ratings - Select model on actual motor full load current
 
Unidrive SP
Normal Duty
Heavy Duty
Max Cont
Current
Typical Motor
Output Power
Max Cont
Current
Typical Motor
Output Power
Modules
Frame
(A)
(kW)
(HP)
(A)
(kW)
(HP)
380-480VAC (kW@400V HP@460V) ±10%

SP1401

 1

2.8

1.1

1.5

2.1

0.75

1.0

SP1402

3.8

1.5

2.0

3.0

1.1

1.5

SP1403

5.0

2.2

3.0

4.2

1.5

3.0

SP1404

6.9

3.0

5.0

5.8

2.2

3.0

SP1405

8.8

4.0

5.0

7.6

3.0

5.0
SP1406
11.0 5.5 7.5 9.5 4.0 5.0

SP2401

 2

15.3

7.5

10.0

13.0

5.5

10.0

SP2402

21.0

11.0

15.0

16.5

7.5

10.0

SP2403

29.0

15.0

20.0

25.0

11.0

20.0
SP2404
29.0 15.0 20.0 29.0 15.0 25.0

SP3401

 3

35.0

18.5

25.0

32.0

15.0

25.0

SP3402

43.0

22.0

30.0

40.0

18.5

30.0

SP3403

56.0

30.0

40.0

46.0

22.0

40
SP4401
4 68 37
50
60 30
50
SP4402
83 45
60
74 37
60
SP4403
104 55
75
96 45
75
SP5401
5 138 75
100
124 55
100
SP5402
168 90
125
156 75
125
SP6401
6 202 110
150
180 90
125
SP6402
236 132
200
210 110
150
 
Panel Mounted Ratings - Select model on actual motor full load current
 
Unidrive SP
Normal Duty
Heavy Duty
Max Cont
Current
Typical Motor
Output Power
Max Cont
Current
Typical Motor
Output Power
Modules
Frame
(A)
(kW)
(HP)
(A)
(kW)
(HP)
500-575VAC (kW@575V HP@575V) ±10%
SP3501
3
5.4
3
3
4.1
2.2
2
SP3502
6.1
4
5
5.4
3
3
SP3503
8.4
5.5
7.5
6.1
4
5
SP3504
11
7.5
10
9.5
5.5
7.5
SP3505
16
11
15
12
7.5
10
SP3506
22
15
20
18
11
15
SP3507
27
18.5
25
22
15
20
SP4603 b
4
36
22
30
27
18.5
25
SP4604 b
43
30
40
36
22
30
SP4605 b
52
37
50
43
30
40
SP4606 b
62
45
60
52
37
50
SP5601 b
5
84
55
75
62
45
60
SP5602 b
99
75
100
84
55
75
SP6601 b
6
125
90
125
100
75
100
SP6602 b
144
110
150
125
90
120
 
Panel Mounted Ratings - Select model on actual motor full load current
 
Unidrive SP
Normal Duty
Heavy Duty
Max Cont
Current
Typical Motor
Output Power
Max Cont
Current
Typical Motor
Output Power
Modules
Frame
(A)
(kW)
(HP)
(A)
(kW)
(HP)
500-690VAC (kW@690V HP@690V) ±10%
SP4601
4
22
18.5
25
19
15
20
SP4602
27
22
30
22
18.5
25
SP4603
36
30
40
27
22
30
SP4604
43
37
50
36
30
40
SP4605
52
45
60
43
37
50
SP4606
62
55
75
52
45
60
SP5601
5
84
75
100
63
55
75
SP5602
99
90
120
85
75
100
SP6601
6
125
110
150
100
90
125
SP6602
144
132
150
125
110
150
 
Dimension in (mm)

Frame Size

 A B C Weight (kg)
1 368 100 219 5*
2 368 155 219 7
3 368 250 260 15
4 510 310 298 30
5 820 310 298 55
6 1131 310 298 75
7        
8        
9        
Dimension in (in)
Frame Size
A
B
C
Weight (lb)
1
14.5
3.9
8.6
11
2
14.5
6.1
8.6
15.4
3
14.5
9.8
10
33.1
4
20.1
12
12
66.1
5
32.3
12
12
121
6
44.5
12
12
165
7
8
9

* SP1405, SP1406 - 5.8kg
 
 
 
    Environment
Ambient Operating Temperature 0º to 40ºC 0º to 50ºC with derating
Cooling method Forced convection
Humidity 95% maximum non-condensing at 40ºC
Storage Temperature -40º to 50ºC
Altitude 0 to 3000m. Derate 1% per 100m between 1000m and 3000m
Vibration Tested in accordance with IEC 68-2-34 Mechanical Shock In accordance with IEC 68-2-27
Enclosure IP 20 (NEMA1), IP 54 (NEMA12) through panel mounting
Electromagnetic Immunity In compliance with IEC801 and EN50082-2, and complies with EN61800-3 with built-in filter
Electromagnetic Emissions In compliance with EN50081-2 when the recommended RFI filter is used and EMC installation guidelines are followed
 
  AC Supply Requirements
Voltage   200 to 240 VAC ±10%
380 to 480 VAC ±10%
500 to 575 VAC ±10%
500 to 690 VAC ±10%
Phase 3Ø
Phase Imbalance Tolerance 2% negative phase sequence (equivalent to 3% voltage imbalance between phases)
Frequency 48 to 65 Hz
Input Displacement Power Factor
0.93
 
  Control
Switching Frequency   3, 4, 6, 8, 12, 16 kHz
Output Frequency 0 to 3000 Hz (Open loop)
Output Speed 0 to 40,000 rpm (Closed loop)
Frequency Accuracy ±0.01% of full scale
Frequency Resolution 0.001 Hz
Analog Input Resolution 16 Bit + sign (Qty 1),10 Bit + sign (Qty 2)
Serial Communications 2 or 4-wire RS232 or RS485. Protocol is ANSI x 3.28-2.5-A4, or Modbus RTU
Baud rate 300 to 115,200
Braking DC injection braking (stopping and holding) standard. Dynamic braking transistor standard
Mains Dip Ride Through Up to 1 second depending on inertia and decel time
 
  Protection
DC Bus Undervoltage Trip   175 / 350 / 435 VDC
(approximately 124 / 247 / 307 VAC line voltage)
DC Bus Overvoltage Trip 415 / 830 / 990 VDC
(approximately 293 / 587 / 700 VAC line voltage)
MOV Voltage 160 Joules, 1400 VDC clamping
Transient Protection (Line to line and line to earth) Drive Overload Trip Current overload value is exceeded. Programmable for Normal Duty or Heavy Duty, Open loop or Closed loop operation
Instantaneous
Overcurrent Trip		 225% of drive rated current Overcurrent Trip
Phase Loss Trip DC bus ripple threshold exceeded
Overtemperature Trips Drive heatsink, control board, and option module(s) monitoring
Short Circuit Trip Protects against output phase to phase fault
Earth Fault Trip Protects against output phase to ground fault
Motor Thermal Trip Electronically protects the motor from overheating due to loading conditions
 
  Approvals & Listings
UL, cUL   Listed E171230
IEC Meets IEC Vibration, Mechanical Shock and Electromagnetic Immunity Standards
CE Designed for marketing
NEMA NEMA 1 enclosure type
VDE Meets VDE Electromagnetic Emissions Standards
ISO9001: 2000 Certified Manufacturing Facility
ISO 14001 Certified Manufacturing Facility
 

The input current is affected by the supply voltage and impedance.

Typical input current
The values of typical input current are given to aid calculations for power flow and power loss. The values of typical input current are stated for a balanced supply.

Maximum continuous input current
The values of maximum continuous input current are given to aid the selection of cables

and fuses. These values are stated for the worst case condition with the unusual

combination of stiff supply with bad balance. The value stated for the maximum

continuous input current would only be seen in one of the input phases. The current

in the other two phases would be significantly lower. The values of maximum input

 current are stated for a supply with a 2% negative phase-sequence imbalance and

rated at the maximum supply fault current.

Model

Typical input current A

Maximum continuous input current A

Cable Size UL 508C

 Cable size EN60204
Fuse rating   Input AWG Output AWG 

Fuse rating IEC gG A

Input mm2

Output mm2

SP1201

7.1

9.5

10
14
18

10

1.5

1

SP1202

9.2

11.3
15
14
16

12

1.5

1

SP1203

12.5

16.4
20
12
14

20

4

1

SP1204

15.4

19.1
20
12
14

20

4

1.5

SP2201

13.4

18.1
20
12
14

20

4

2.5

SP2202

18.2

22.6
25
10
10

25

4

4

SP2203

24.2

28.3
30
8
8

32

6

6

SP3201

35.4

43.1
45
6
6

50

16

16

SP3202

46.8

54.3
60
4
4

63

25

25

SP1401

4.1

4.8
6
18
22

6

1

1

SP1402

5.1

5.8
6
16
20

6

1

1

SP1403

6.8

7.4
10
16
18

8

1

1

SP1404

9.3

10.6
15
14
16

12

1.5

1

SP1405

10

11
15
14
14

12

1.5

1

SP1406

12.6

13.4
15
14
14

16

2.5

1.5

SP2401

15.7

17
20
12
14

20

4

2.5

SP2402

20.2

21.4
25
10
10

25

4

4

SP2403

26.6

27.6
30
8
8

32

6

6

SP3401

34.2

36.2
40
6
6

40

10

10

SP3402

40.2

42.7
45
6
6

50

16

16

SP3403

51.3

53.5
60
4
4

63

25

25

SP3501

5

6.7
10
16
18

8

1

1

SP3502

6

8.2
10
16
16

10

1

1

SP3503

7.8

11.1
15
14
14

12

1.5

1

SP3504

9.9

14.4
15
14
14

16

2.5

1.5

SP3505

13.8

18.1
20
12
14

20

4

2.5

SP3506

18.2

22.2
25
10
10

25

4

4

SP3507

22.2

26
30
8
8

32

6

6
* Use Fuse class RK1 or similar HRC fuse.

Home / Contact Us / Products / Service / Sales /Supported Product / Powertec Support / Serviced Products / Feedback

 

Microcon Technologies Inc.

1105 Crestlawn Drive, Unit # D8 & D9

Mississauga, Ontario L4W 1A7 Canada

Tel: (905) 602-4770

Fax: (905) 602-4779

e-mail: sales@microcontechnologies.com

Website: www.microcontechnologies.com